FINISAR XGIG TRACE VIEWER FREE DOWNLOAD

Thus, essentially the software predetermines which event needs to be fed to which expert and then the experts can look at the individual commands as they get sent to them. Apply power to the chassis and establish communication with the chassis. For this peripheral qualifier the peripheral device type shall be set to 1Fh to provide compatibility with previous versions of SCSI. This provides the user the unique ability to only focus analysis only on valid communications occurring in the loop or network. FC is a general name for an integrated set of standards being developed by ANSI American National Standards Institute whose purpose is to act as a universal high-speed interface for computers and mass storage.

Uploader:	Kajitaur
Date Added:	10 March 2008
File Size:	33.76 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	8027
Price:	Free* [*Free Regsitration Required]

For example, targets generally have a maximum number of pending exchanges that can be handled at one time.

Xgig 8G Fibre Channel Analyzer

When you launch the diagnostic routine, the Xgig Server Start Diagnostic page appears. A user can also correlate the vieer of transfer mode Uses with the number of Arbitration Wins for a specific port.

A solid green light means that the Xgig operating system is up and running and has obtained a valid IP address.

Lower values indicate inefficiencies in transmission, and these inefficiencies can include poor frame management techniques by the initiator as well as poor PCI performance from the host system. For example, the software may save this information in the trace file or other associated data file so that subsequent analysis runs will have access to the information and will not require duplicate preprocessing or input steps.

SANMetrics uses techniques to capture and display these counters as accurately as possible, although there are cases where these counters are collected on a best approximation basis.

Further, the topology detection view is configured to list the errors and warnings further discussed herein that were identified and generated in the analysis process generally conducted separately and subsequently from the topology detection processwhile graphically indicating a location on the network the caused each error or warning. Enter the user name and password you normally use to log on to the Xgig chassis. When you log in using a secure connection, fiinisar lock icon appears on the status bar at the bottom of the web fibisar.

Additionally, if the SCSI operations consist of a mixture of Random reads, the ECT will generally increase due to the additional seek time introduced between operations. For SCSI or FC pending exchanges counters, generally, the most critical characteristic to finisra in the trace is the pending exchanges or Queue Depth. Once the target starts completing the group of pending exchanges, it will generally complete multiples due to data caching and other read-ahead features.

Thus, when a user places the analyzer in a switched fabric environment, the ability to capture a single trace that shows all of the interactions of the participating components may be lost. It is universal, open and an easy to use protocol. There are several capture configurations that will provide maximum capture time with a minimal amount of captured information. It is using too many tenancies to vifwer data. Physical connection to your local area network A socket outlet supplying V power or V for international.

Leave xgigg server up and running to access upgrades. The maximum number of pending exchanges a target can handle varies for the different manufacturers and varies based upon the size of bytes requested in the exchange.

Several factors determine placement of an analyzer in relation to the components that are being measured. The source port initiates a new tenancy by arbitrating for the loop and then transmitting OPN to the destination port. Note that the number of memory modules on one side of the blade depends on the type vviewer blade.

Xgig 8G Fibre Channel Analyzer - PDF

Note that Windows Vista uses Internet Explorer 7. The Memory Modules lie flat against the blade. For security reasons, if authentication is enabled for a chassis, you must login directly to that chassis to upgrade the images. Connect the Cascade Out port on the master Xgig chassis to the Cascade In port on the next chassis in the chain. If you still cannot get a connection, call Customer Xgif. The analysis of these conversations, however, requires implementation of a great deal of code to emulate both the protocol Initiator and Target.

Check the box for System Fiisar or System B.

The list of events that clear the exchange information includes an FLOGI frame clears any pending exchanges fknisar the source and destination, a PLOGI frame clears any pending exchanges between the finizar and destination, a TPRLO Third Finizar Process Logout frame clears any pending exchanges between the destination and any source, a LOGO frame, which should come from the responder, clears any pending exchanges between the source and destination, a SCSI target Reset command frame clears any pending exchanges between the destination and any source, and an FC P-2 LUN reset will clear exchanges to between the source and the specified LUN on the destination.

Current System Backup System If the boot selection message does not appear, check the cable between the PC or terminal and the Xgig chassis.

This peripheral qualifier does not imply that the device is ready for access by the initiator. Note that this assumes that the ports are using the alternate credit model with a buffer to buffer credit value of 0.

So some things flow within the samples, and the user can look at data rate, this is just a number of bytes that are vifwer in that sample, but most of the time this starts in the FC- FC-2 and SCSI protocols going through their own behavior sequence start.

Start display at page:.